top of page

Subfloor Preparation for SPC Flooring: Flatness, Moisture and Cleaning Checklist

Nov 5
3 min read

Quick Answer

Subfloor preparation for SPC flooring has three jobs: make the surface flat, make it dry and make it clean. Most installation guides ask for a subfloor flat to about 3 mm over 2 m, within the moisture limit of the guide, and free of dust, paint, adhesive residue and loose material. Skipping any of the three is the most common cause of joint noise and open gaps.


Introduction

SPC flooring is rigid, so it hides small surface marks better than soft vinyl. That leads many installers to rush the subfloor. The rigid core also means a high or low spot is not absorbed. It is carried into the locking joints, where it turns into movement, noise or a visible gap. A short, careful preparation routine prevents most callbacks.


Subfloor Preparation for SPC Flooring: The Checklist

Check

What to look for

Typical action

Flatness

High and low spots beyond the guide’s tolerance, often about 3 mm over 2 m

Grind high spots, fill low spots with levelling compound

Moisture

Readings above the limit in the installation guide

Wait, dry the slab or install a moisture barrier

Cleanliness

Dust, adhesive, paint, oil or old floor residue

Scrape, sweep and vacuum

Cracks and damage

Open cracks, loose screed, damaged boards

Repair before installing

Temperature

Cold or hot subfloor at installation

Stabilise the room before and during the job

Concrete subfloor preparation for SPC flooring showing a moisture meter, leveling compound, and cleaning tools.

Flatness

Place a straight edge on the subfloor and look for gaps. When a click joint sits over a dip, it can flex each time someone walks across it. That flexing is a main source of the clicking and popping described in our guide on why SPC flooring makes noise.


Moisture

Concrete slabs should be tested before installation. Typical manufacturer limits sit around 75 to 85 percent relative humidity or about 2.5 to 3 percent by CM method, but the number in the product’s own installation guide always applies. SPC itself does not swell, but moisture can still affect underlay, adhesives and any wood subfloor below it.


Cleanliness

A small stone or screw head under a plank can create a hard spot that wears through the surface or breaks a lock. Vacuum the full area, not only the visible parts.


Common Subfloor Mistakes

• Installing over a floor that has not been checked with a straight edge.

• Skipping the moisture test on a new slab.

• Leaving old adhesive ridges in place.

• Using a levelling compound that was not allowed to cure.


What This Looks Like for Yosemite’s Flooring Range

Yosemite’s SPC, LVT and LSPC lines use click installation, so the subfloor sets the quality of the joints. The same preparation rules apply across the lines, but exact tolerances and moisture limits depend on the product, so ask our team for the installation guide that matches your selected range before the job starts. Once the subfloor is ready, plan the gap around the room with our guide to expansion gaps for SPC flooring.

About Yosemite Flooring. Yosemite Flooring (Anhui Yosemite New Material Technology Co., Ltd.) manufactures LVT, SPC, LSPC and ABA SPC flooring for importers, distributors and project buyers, with production bases in China, Vietnam and Thailand. Its environmental performance is documented in third-party EPDs published in the International EPD System, including EPD-IES-0018227 for LSPC and EPD-IES-0018226 for LVT. Explore the full range at yosemiteflooring.com.


Frequently Asked Questions

Q: Can SPC flooring go over uneven concrete?

A: Only within the flatness tolerance in the installation guide. Larger variations need grinding or levelling first.


Q: Do I need to test moisture for SPC flooring?

A: Yes on concrete. SPC does not absorb water, but moisture still affects the system around it and may affect warranty terms.


Q: Can I install SPC over old tiles?

A: Often yes if the tiles are firmly fixed, but deep grout lines may need to be filled so they do not print through or weaken the joints.


Q: What tool checks flatness?

A: A straight edge or a long level, plus a feeler gauge for the size of any gap.


Final Thoughts

Subfloor preparation for SPC flooring is a short job that decides whether the click joints stay tight for years. Check flatness, moisture and cleanliness, repair what is out of tolerance and follow the guide for your product. The extra hour usually saves a callback.

If you would like to get more information from us, please follow our Instagram.

Comments


bottom of page