top of page

Expansion Gaps for SPC Flooring: How Much Space Does a Floating Floor Need?

Nov 5
3 min read

Quick Answer

An expansion gap for SPC flooring is the small space left between the floating floor and every wall, fixed object and vertical surface. Most installation guides ask for roughly 5 to 10 mm around the perimeter, and the number printed in the product’s own guide always takes priority. The gap lets the floor expand and contract with temperature without buckling or opening at the joints.


Introduction

SPC flooring moves much less than soft vinyl or laminate, which leads some installers to treat the gap as optional. It is not. A rigid floating floor that is pinned at the edges has nowhere to go when a sunny window heats it, and the stress ends up in the locking joints. Leaving the right gap is quick, and it prevents peaking, open seams and noise.


Expansion Gap for SPC Flooring: Typical Values by Situation

Situation

Typical gap

Note

Perimeter walls

About 5 to 10 mm

Follow the product’s installation guide

Door frames and thresholds

Same as perimeter

Undercut frames where possible instead of cutting a tight fit

Pipes and fixed columns

Same as perimeter

Cover with a pipe collar or rose

Large open areas or long runs

Add a movement joint

Many guides limit continuous runs, so check the guide

Rooms with large sun-facing glass

Use the upper end of the range

Surface temperature can rise sharply

Why the gap still matters for rigid SPC

SPC has a dense, stable core, so movement is small, but it is not zero. Over a long room or a sun-exposed floor, small movement adds up, and the gap is where it goes.


What should not touch the floor

Skirting boards, door frames, cabinets and any fixed element should leave the floating floor free to move. Do not screw or glue the planks to the subfloor, and do not fix heavy cabinets on top of the floor, such as kitchen islands, unless the guide says it is allowed.


How to Leave the Gap Step by Step

• Place spacers of the right thickness against the wall as you install each row.

• Keep the gap clear of adhesive, filler and debris.

• Fit the skirting after the floor, so it covers the gap without pressing on the planks.

• Use T-moulding or a movement joint across doorways and in long or wide runs.

• Remove spacers only when the floor is complete.


SPC flooring installation showing red and blue spacers maintaining a proper expansion gap along the wall, with a rubber mallet and tools nearby.

Signs That the Gap Was Too Small

• A raised ridge, or peaking, along a joint.

• Joints that open when the room is cold.

• Clicking or creaking near walls and doorways, which is also covered in our guide on why SPC flooring clicks or pops.


What This Looks Like for Yosemite’s Flooring Range

Yosemite’s SPC, LVT and LSPC lines are click-lock floating floors, so the expansion gap rule applies across them. The exact gap and maximum run length depend on the product, so ask our team for the installation guide for your selected line. A flat, clean surface is the other half of a good installation, as described in our guide to subfloor preparation for SPC flooring.

About Yosemite Flooring. Yosemite Flooring (Anhui Yosemite New Material Technology Co., Ltd.) manufactures LVT, SPC, LSPC and ABA SPC flooring for importers, distributors and project buyers, with production bases in China, Vietnam and Thailand. Its environmental performance is documented in third-party EPDs published in the International EPD System, including EPD-IES-0018227 for LSPC and EPD-IES-0018226 for LVT. Explore the full range at yosemiteflooring.com.


Frequently Asked Questions

Q: How big is the expansion gap for SPC flooring?

A: Typically 5 to 10 mm, but use the figure in the installation guide for the product.


Q: Do I need a gap if the room is small?

A: Yes. A smaller room moves less, but a floating floor still needs a gap at every wall.


Q: Can I fix kitchen cabinets on top of SPC flooring?

A: Usually it is better to install cabinets first and fit the floor around them, so the floor is not pinned.


Q: When do I need a movement joint?

A: In doorways, in long or wide runs and when the guide sets a maximum continuous area.


Final Thoughts

The expansion gap for SPC flooring is a small detail with a large effect. Leave the gap the guide asks for, keep the floor free at every edge and add movement joints where the area is large. The floor will stay flat and quiet.

If you would like to get more information from us, please follow our Instagram.

Comments


bottom of page